Videos that might interest you:
Retraction Calibration https://youtu.be/KwcKX3o3kCU
Cura 3 - How To Examples https://youtu.be/bJiKIPtyMgc
How To Dismantle The Hot End https://youtu.be/xOeSjzwnBqM
Top 5 Features Cura 3.2 https://youtu.be/HI4tv7EsbQk
How to Clean a 3D Printer Nozzle https://youtu.be/hBkTeXxcFi8
Cura Time Saver Setting https://youtu.be/82VAfwyS_Cs

In this video, we will look at the different extrusions rate problems. You can have over extrusion and under extrusion or just the right amount.

So I will show you the look of something that is over extruded, correct extrusion and under extrusion. You will see an example of each. And how to recognize this problem.

Then I will demonstrate how to measure the extrusion rate of your 3D printer, with a simple technic, and a direct way to calculate the percentage of correction needed.

And finally a quick word on how to adjust the rate the easily.


My gear :

Amazon US (Commissions Earned):
Filament used PETG MG Chemicals http://amzn.to/2gWBJdnHictop 3D Printer model 3DP-11-ATL http://amzn.to/2yF9FEY
3D Printer Monoprice Select Mini V2 http://amzn.to/2yK9TdV
Camera Sony A6300 http://amzn.to/2gWmaTi
Sigma Lens 30mm F1.4 http://amzn.to/2gtzeyL
Neewer 7" Field Monitor http://amzn.to/2gWAsD7
Neewer Accessories http://amzn.to/2xcYobL
SanDisk Extreme 64GB SDXC UHS-I Card http://amzn.to/2yF34di
Manfrotto Compact Tripod http://amzn.to/2yEIZnv
IMDEN Omnidirectional Condenser Lavalier Microphone http://amzn.to/2xcY4cR

Amazon Canada (Commissions Earned):
Filament used PETG MG Chemicals http://amzn.to/2xdKo1v
3D Printer model 3DP-11-ATL http://amzn.to/2xdgyKq
3D Printer Monoprice Select Mini V2 http://amzn.to/2yKAUhn
Camera Sony A6300 Kit http://amzn.to/2gVrhD4
Sigma Lens 30mm F1.4 http://amzn.to/2xWO2kJ
Neewer 7" Field Monitor http://amzn.to/2zqL97K
Neewer Accessories http://amzn.to/2gVrshI
SanDisk Extreme 64GB SDXC UHS-I Card http://amzn.to/2gVrw0W
Manfrotto Compact Tripod http://amzn.to/2xVgChk
IMDEN Omnidirectional Condenser Lavalier Microphone http://amzn.to/2xX4lOs




Hi, I'm Frank my channel is all about 3D printing. I can't get enough of my 3D printer. I make everything and anything out of 3D filament (PLA, PETG and more). As I say a printer that is not printing is a missed opportunity.

I'll be doing electronics, mechanics, computer engineering, DIY, reviews and tutorials.

I update twice a week on Tuesday and Saturdays.

Subscribe to my channel, and don't forget to turn on notifications.

You can also find me on :
Facebook: https://www.facebook.com/Franks-3D-Shop-567006427024034/
Twitter: https://twitter.com/Franks3dshop
Instagram: https://www.instagram.com/franks3dshop/